Materialwissenschaft und Werkstofftechnik

Most Accessed 04/2025

• B.O. Gerhards, B. Gerhards, B. Macke, P. Häuser, M. Schleser, P. Liebe
  Overlap joining of EN AW 7075 with laser beam welding in vacuum [Article]
  Mat.-wiss. u. Werkstofftech 2025, vol. 56, no. 3, p. 376
• P. Taweekitikul, A. A. Aliyu, D. Decha-Umphai, S. Tantavisut, J. Khamwannah, C. Puncreobutr, B. Lohwongwatana
  Synthesis, characterization, and interfacial adhesion of titania iodine-doped nanotubes architectures on additively manufactured Ti-6Al-4V implant [Article]
  Mat.-wiss. u. Werkstofftech 2025, vol. 56, no. 3, p. 438
• S. Bakhtiari, S. S. Sharifi, S. Ilie, C. Sommitsch
  Investigation of hot ductility behavior of micro-alloyed steel and the effect of strain rate and dynamic phase transformation on the 2^nd ductility minimum [Article]
  Mat.-wiss. u. Werkstofftech 2025, vol. 56, no. 4, p. 601
• P. Kubaschinski, A. Gottwalt, U. Tetzlaff, H. Altenbach, M. Waltz
  Calibration of a combined isotropic-kinematic hardening material model for the simulation of thin electrical steel sheets subjected to cyclic loading [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 4, p. 422
• C.W. Ng, A.S. Mahmud, M.N. Ahmad, M.F. Razali, Y. Liu
  Estimation of titanium oxide layer thickness on thermally oxidized NiTi alloy based on color variations [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 1, p. 47
• C. Hopmann, D. C. Fritsche, C. E. Kahve, K. Bobzin, H. Heinemann, M. Erck, C. Vogels
  Methodology of a thermal injection mold design with locally applied heating coatings on the cavity wall [Article]
  Mat.-wiss. u. Werkstofftech 2024, vol. 55, no. 4, p. 518
• M. Aslam, T. Khan, M. Basit, R. Masood, Z.A. Raza
  Polyacrylonitrile-based electrospun nanofibers - A critical review [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 12, p. 1575
• A. Suryawanshi, N. Behera
  Dental composite resin: a review of major mechanical properties, measurements and its influencing factors [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 5, p. 617
• M. Schwarz, R. Glienke, F. Wegener, C. Blunk, K.-M. Henkel
  Calculation of lockbolt joints in mechanical engineering [Article]
  Mat.-wiss. u. Werkstofftech 2020, vol. 51, no. 3, p. 267
• E. Maghsoudi Nia, N.A. Wan Abdullah Zawawi, B.S. Mahinder Singh
  Design of a pavement using piezoelectric materials [Article]
  Mat.-wiss. u. Werkstofftech 2019, vol. 50, no. 3, p. 320
• B.M. Schönbauer, M. Killinger, U. Karr, M. Fitzka, U. Müller, A. Teischinger, H. Mayer
  Fatigue properties of wood at different load ratios tested at 50 Hz and 20 kHz [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 3, p. 344
• T. Reiber, J. Rüdesheim, M. Weigold, E. Abele, J. Musekamp, M. Oechsner
  Influence of contour scans on surface roughness and pore formation using Scalmalloy® manufactured by laser powder bed fusion (PBF-LB) [Article]
  Mat.-wiss. u. Werkstofftech 2021, vol. 52, no. 4, p. 468
• B. Panda, Y.W.D. Tay, S.C. Paul, M.J. Tan
  Current challenges and future potential of 3D concrete printing [Article]
  Mat.-wiss. u. Werkstofftech 2018, vol. 49, no. 5, p. 666
• F. Kraemer, T. Binder, M. Klein, M. Oechsner
  Experimentelle und rechnerisch validierte Methode zur Bestimmung der Mindesteinschraubtiefe von Schraubenverbindungen mit gefurchtem Mutterngewinde [Article]
  Mat.-wiss. u. Werkstofftech 2025, vol. 56, no. 2, p. 305
• A. Gottwalt-Baruth, P. Kubaschinski, M. Waltz, U. Tetzlaff
  Influence of shear cutting parameters on the edge properties and the fatigue behavior of non-oriented electrical steel sheets [Article]
  Mat.-wiss. u. Werkstofftech 2025, vol. 56, no. 4, p. 537

Most Accessed 05/2024 to 04/2025

• P. Kubaschinski, A. Gottwalt, U. Tetzlaff, H. Altenbach, M. Waltz
  Calibration of a combined isotropic-kinematic hardening material model for the simulation of thin electrical steel sheets subjected to cyclic loading [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 4, p. 422
• M. Hofele, J. Schanz, A. Roth, D.K. Harrison, A.K.M. De Silva, H. Riegel
  Process parameter dependencies of continuous and pulsed laser modes on surface polishing of additive manufactured aluminium AlSi10Mg parts [Article]
  Mat.-wiss. u. Werkstofftech 2021, vol. 52, no. 4, p. 409
• M. Brozio, L.-S. Apfelbacher, L. Hitzler, C. Krempaszky
  Feasibility study on hybrid manufacturing - combining laser-based powder-bed fusion and chill casting on the example of EN AC-42000 alloy [Article]
  Mat.-wiss. u. Werkstofftech 2024, vol. 55, no. 5, p. 610
• I. Raffeis, U. Vroomen, F. Adjei-Kyeremeh, D. Großmann, H. Hammelrath, E. Westhoff, S. Bremen, D. Boscolo Bozza, A. Bührig-Polaczek
  Comparative investigations into microstructural and mechanical properties of as-cast and laser powder bed fusion (LPBF) fabricated duplex steel (1.4517) [Article]
  Mat.-wiss. u. Werkstofftech 2020, vol. 51, no. 4, p. 432
• W. Tillmann, L. Hagen, K.-U. Garthe, K.-P. Hoyer, M. Schaper
  Effect of substrate pre-treatment on the low cycle fatigue performance of tungsten carbide-cobalt coated additive manufactured 316 L substrates [Article]
  Mat.-wiss. u. Werkstofftech 2020, vol. 51, no. 11, p. 1452
• C.W. Ng, A.S. Mahmud, M.N. Ahmad, M.F. Razali, Y. Liu
  Estimation of titanium oxide layer thickness on thermally oxidized NiTi alloy based on color variations [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 1, p. 47
• T. Reiber, J. Rüdesheim, M. Weigold, E. Abele, J. Musekamp, M. Oechsner
  Influence of contour scans on surface roughness and pore formation using Scalmalloy® manufactured by laser powder bed fusion (PBF-LB) [Article]
  Mat.-wiss. u. Werkstofftech 2021, vol. 52, no. 4, p. 468
• M. Schwarz, R. Glienke, F. Wegener, C. Blunk, K.-M. Henkel
  Calculation of lockbolt joints in mechanical engineering [Article]
  Mat.-wiss. u. Werkstofftech 2020, vol. 51, no. 3, p. 267
• K. Bobzin, T. Brögelmann, C. Kalscheuer, M. Thiex
  Formation mechanisms of zinc, molybdenum, sulfur and phosphorus containing reaction layers on a diamond-like carbon (DLC) coating [Article]
  Mat.-wiss. u. Werkstofftech 2020, vol. 51, no. 7, p. 1009
• P. Maire, M. Deckert, M. Johlitz, A. Öchsner
  Characterisation of the mechanical properties of polyamide 12 powder when using titanium dioxide as antimicrobial additive [Article]
  Mat.-wiss. u. Werkstofftech 2023, vol. 54, no. 4, p. 385
• B.M. Schönbauer, M. Killinger, U. Karr, M. Fitzka, U. Müller, A. Teischinger, H. Mayer
  Fatigue properties of wood at different load ratios tested at 50 Hz and 20 kHz [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 3, p. 344
• B. Blinn, S. Greco, M. Smaga, M. Zimmermann, H. Hotz, D. Müller, J. Hartig, B. Kirsch, J.C. Aurich, T. Beck
  Influence of microstructural defects and the surface topography on the fatigue behavior of “additively-subtractively” manufactured specimens made of AISI 316L [Article]
  Mat.-wiss. u. Werkstofftech 2021, vol. 52, no. 5, p. 561
• A. Suryawanshi, N. Behera
  Dental composite resin: a review of major mechanical properties, measurements and its influencing factors [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 5, p. 617
• P. Maire, E. Sert, M. Deckert, M. Johlitz, A. Öchsner
  Characterisation of the thermal ageing effects on the mechanical properties when reusing polyamide 12 in the selective laser sintering process [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 4, p. 503
• C. Spurk, S. Hollatz, W. Lipnicki, M. Hummel, A. Gillner, C. Häfner
  Controlling the weld penetration depth of laser beam micro welding by using an iterative learning approach [Article]
  Mat.-wiss. u. Werkstofftech 2024, vol. 55, no. 4, p. 533
• M. Aslam, T. Khan, M. Basit, R. Masood, Z.A. Raza
  Polyacrylonitrile-based electrospun nanofibers - A critical review [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 12, p. 1575
• L. Xie, H. Wei, L. Kou, L. Ren, J. Zhou
  Antibiotic drug release behavior of poly (vinyl alcohol)/sodium alginate hydrogels [Article]
  Mat.-wiss. u. Werkstofftech 2020, vol. 51, no. 7, p. 850
• B. Heine, A. Kah, M. Sedlmajer, C. Ocker, M. Merkel
  Impact of corrosion on mechanical properties of additively manufactured Invar 36 [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 3, p. 316
• K. Demirelli, A. Çelik, Y. Aksoy, M. Yegin, E. Barım, Ö. Hanay, H. Hasar
  Synthesis process, thermal and electrical behaviors of Ti₃C₂T_x MXene [Article]
  Mat.-wiss. u. Werkstofftech 2024, vol. 55, no. 9, p. 1213
• S. Tillmann, M. Behr, S. Elgeti
  Using Bayesian optimization for warpage compensation in injection molding [Article]
  Mat.-wiss. u. Werkstofftech 2024, vol. 55, no. 1, p. 13
• C. Hopmann, D. C. Fritsche, C. E. Kahve, K. Bobzin, H. Heinemann, M. Erck, C. Vogels
  Methodology of a thermal injection mold design with locally applied heating coatings on the cavity wall [Article]
  Mat.-wiss. u. Werkstofftech 2024, vol. 55, no. 4, p. 518
• K. Mäde, P. J. Kellerwessel, R. Sharma, U. Reisgen
  A-prori layer height determination for wire arc additive manufacturing based on weld geometry [Article]
  Mat.-wiss. u. Werkstofftech 2024, vol. 55, no. 7, p. 995
• M. Fiedler, J. Weichert, R. Rennert
  Zyklische Auslastungsgrade der FKM-Richtlinien: Definition und Vorschlag eines effizienten Iterationsverfahrens [Article]
  Mat.-wiss. u. Werkstofftech 2023, vol. 54, no. 11, p. 1454
• P. Michels, O. Bruch, B. Evers-Dietze, D. Grotenburg, E. Ramakers-van Dorp, H. Altenbach
  Shrinkage simulation of blow molded parts using viscoelastic material models [Article]
  Mat.-wiss. u. Werkstofftech 2022, vol. 53, no. 4, p. 449
• K. Bobzin, H. Heinemann, M. Erck, S. Warkentin, O. Mokrov, R. Sharma, U. Reisgen, K. Jasutyn
  Modeling of arcs with binary gas mixtures in a multi-arc plasma generator [Article]
  Mat.-wiss. u. Werkstofftech 2025, vol. 56, no. 1, p. 77